Introduction to the application of 10kW gasoline generator in small cars: gasoline generator startup and operation:

《1》機組啟動后，讓啟入手柄借助回彈啟動器自動回收啟動盤，不允許在汽油機工作時再

《1》 After the unit is started, let the starting handle automatically recover the starting disk with the help of the rebound starter, and it is not allowed to recover the starting disk when the gasoline engine is working

拉起動輪，以防啟動機構損壞，汽油機啟動后逐步開大風門，直至完整翻開，調理節氣門

Pull up the driving wheel to prevent damage to the starting mechanism. After the gasoline engine is started, gradually open the large air valve until it is completely opened, and adjust the throttle

，使汽油機在低速狀態下運轉2~3分鐘，使光滑油能平均地布在各磨擦面上。

Make the gasoline engine run at low speed for 2-3 minutes, so that the smooth oil can be evenly distributed on each friction surface.

《2》機組在通風良好的條件下運用，避免廢氣排放，不暢形成其工作條件惡化和操作

《2》 The unit is operated under the condition of good ventilation, so as to avoid exhaust gas emission and poor working conditions and operation

人員廢氣中毒現象產生。

Personnel exhaust gas poisoning.

《3》機組需中止工作時，應切斷負載電源讓發起機在空載條件下運轉1~2分鐘左右，

《3》 When the unit needs to stop working, first cut off the load power supply and let the starter run for about 1~2 minutes under no-load conditions,

關閉燃油開關，使點火開關設在“off“位置，使汽油機終止工作。

Turn off the fuel switch and set the ignition switch to the "off" position to stop the gasoline engine.

《4》檢查油箱有無燃油，無油時應按規則牌號添加。

《4》 Check whether there is fuel in the oil tank. If there is no fuel, add it according to the rule brand.

小型車上用10KW汽油發電機運用引見：上海歐鮑實業有限公司的主要產品有：汽油發電機組、汽油發電機組、汽油發電電焊機、

Introduction to the application of 10kW gasoline generator for small cars: the main products of Shanghai oubao Industrial Co., Ltd. are: gasoline generator set, gasoline generator set, gasoline generator welding machine

汽油發電機組，以及靜音發電機組和 數碼變頻發電機組。

Gasoline generator set, silent generator set and digital frequency conversion generator set.

的技術優勢和制造經歷，全線引進日本的制造設備、消費工藝和檢測安裝，按照

With advanced technical advantages and manufacturing experience, Japan's advanced manufacturing equipment, consumption technology and testing installation are introduced throughout the line, according to

大澤原廠的質量規范，并采用好新技術，使發電機質量和技術性能到達程度，是的油氣建

Daze's original quality specifications, and the use of new technology, so that the generator quality and technical performance to reach the level, is the oil and gas construction

設單位、鐵路、市政管網、化工廠、發電廠、鋼鐵廠內施工與搶險維修

Construction and emergency maintenance of design units, railways, municipal pipe networks, chemical plants, power plants, and steel plants

值得信任的應急設備消費提供商.

A trusted consumer provider of emergency equipment

小型車上用10KW汽油發電機運用引見：發電機不能正常起動的處置辦法：

Introduction to the application of 10kW gasoline generator in small cars: the disposal method of generator unable to start normally:

（1）檢查火花塞有無異常。

(1) Check whether the spark plug is abnormal.

（2）檢查發電機開關能否在“關”位置，若是，請摁到“開”位置。

(2) Check whether the generator switch is in the "off" position. If so, press it to the "on" position.

（3）檢查油箱能否有油，若無油請先將油加到位，然后再起動。

(3) Check whether there is oil in the oil tank. If there is no oil, please fill it in place before starting.

（4）假如上述3種狀況均正常，則再做以下檢查：

(4) If the above three conditions are normal, then do the following inspection:

《1》 燃油過濾器能否阻塞。

《1》 Whether the fuel filter is blocked.

《2》 油箱開關能否阻塞。

《2》 Whether the fuel tank switch is blocked.

以上就是為大家介紹的有關190發電機組配件的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以專業的態度,為您提供服務.http://dgtmcnc.com

The above is a detailed introduction about the accessories of 190 generator set. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://dgtmcnc.com