Precautions when installing the generator

大家在選購發電機時，一般都是會有工作人員來進行安裝調試，這樣是為了確保在運行中不會出現問題，那么大家知道在安裝發電機時需要注意什么嗎？下面發電機廠家小編和大家聊一聊安裝發電機時的注意事項。

When purchasing generators, people usually have staff to install and debug them, so as to ensure that there will be no problems in operation. Do you know what to pay attention to when installing generators? Next, the generator manufacturer  sent to talk about the precautions when installing the generator.

1、檢查潤滑油的油位。如果油位不足的情況下，難以達到了理想的潤滑效果，就會造成磨損現象會很嚴重的。這樣的話，就會對質量方面會造成了直接的影響。所以說這需要對冷卻液的液位、燃油量和油位方面都要認真的去檢查一下，確保達到了標準的位置才行，在安裝使用上更加安*的。

1. Check the lubricating oil level. If the oil level is insufficient, it is difficult to achieve the ideal lubrication effect, which will cause serious wear. In this way, it will have a direct impact on the quality. Therefore, it is necessary to carefully check the coolant level, fuel quantity and oil level to ensure that the standard position is reached, and it is more safe in installation and use.

2、電氣線路的故障或者漏電現象上，也是不能忽視的。因此，安裝發電機之前，都要做好詳細的檢查，要看看電氣線路在接地或者連接的時候是否達到了更加牢固的效果。因此，這在安裝之前都要對這方面的細節要點上都要合理的去把握好才行，這樣才能夠恢復正常的運行。

2. The failure or leakage of electrical circuits can not be ignored. Therefore, before installing the generator, it is necessary to make a detailed inspection to see whether the electrical circuit has achieved a more solid effect when it is grounded or connected. Therefore, before installation, we should reasonably grasp the details and key points in this regard, so as to restore normal operation.

3、在啟動的時候，對每一個部位的燃油系統空氣方面需要進行排空才行。只有排空的情況下才會更加安*的。所以說，發電機在這方面安裝前都要做好相應的檢查，確保在這方面的檢查要點上要合理的去把握好，才能夠在每一個要點上嚴格的去控制好，這一切都是要抓住了其中的要點和細節才行。

3. When starting, the air of the fuel system at each part needs to be drained. It will be safer only when it is empty. Therefore, before the installation of the generator in this regard, the corresponding inspection should be done to ensure that the inspection points in this regard should be reasonably grasped, so that each point can be strictly controlled. All these should grasp the key points and details.

本文的精彩內容由煉化尾氣發電機組提供知識提供，本網站還有很多的精彩內容，更多的內容您可以點擊進入：http://dgtmcnc.com 我們有專門的客服為您解答問題

The wonderful contents of this article are provided by the refining and chemical tail gas generator set. There are many wonderful contents on this website. You can click to enter more contents: http://dgtmcnc.com We have special customer service to answer your questions