The natural gas generator set has good power generation quality, fast start-up, stable operation and many advantages. But this also needs to pay attention to some matters when using. For example, startup and shutdown of the unit. The small editor introduced that the startup and shutdown of natural gas generator set should be done one by one, and the steps should be clear!

一、天然氣發電機組在開機前要注意燃氣管系、燃氣部件的安裝、傳感器與控制屏組合模擬檢測等事項。接下來的機組來及事項要注意：

1、 Before starting the natural gas generator set, pay attention to the installation of gas pipeline system and gas components, combined simulation detection of sensor and control panel, etc. Notes for the next unit:

1、開機前，應清理機組（旋轉部件）上放置的雜物（如盤車杠、工具、螺釘?shù)龋?，以免開車時工件飛出去傷人。

1. Before start-up, the sundries (such as turning bar, tools, screws, etc.) placed on the unit (rotating parts) shall be cleaned to prevent the workpiece from flying out and hurting people during start-up.

2、開機前手動盤車時，注意先斷開起動電源，以免誤觸動起動按鈕，盤車杠飛出去傷人。

2. When turning manually before startup, pay attention to disconnect the starting power supply first, so as not to touch the start button by mistake, and the turning rod will fly out and hurt people.

二、天然氣發電機組運行要求

2、 Operation requirements of natural gas generator set

1、啟動時，先踏下腳踏開關，按下啟動按鈕，將缸內燃氣排空后再開啟燃氣閥門，嚴禁先給燃氣再按啟動按鈕。啟動不成功或啟動后又熄火時，應關閉燃氣閥門，查清原因，排凈缸內混合氣體后，再按規定程序重新啟動。啟動成功后，應踢開腳踏開關。

1. When starting, first step on the foot switch, press the start button, empty the gas in the cylinder, and then open the gas valve. It is strictly prohibited to supply gas first and then press the start button. In case of unsuccessful startup or flameout after startup, close the gas valve, find out the cause, exhaust the mixed gas in the cylinder, and then restart according to the specified procedures. After successful startup, kick off the foot switch.

2、開機時，打開門窗，開動排風裝置，直到停機。

2. When starting up, open the doors and windows and start the exhaust device until it stops.

3、.操作者在機房內操作時，應戴安全帽或頭盔，機器運轉過程中不能直接面對防爆門，應避開飛輪等高速旋轉件，不能觸摸排氣管等高溫件。

3、. When operating in the machine room, the operator shall wear safety helmet or helmet. During the operation of the machine, the operator shall not directly face the explosion-proof door, avoid high-speed rotating parts such as flywheel, and shall not touch high-temperature parts such as exhaust pipe.

4、運行中，若發現燃氣有泄漏情況，操作人員應卸掉負荷并停機檢查。

4. In case of gas leakage during operation, the operator shall unload the load and stop the machine for inspection.

5、機組運行時，注意燃氣發動機防爆安全門，一旦爆破（其聲音較大）應關閉氣源，換防爆膠皮后方可重新啟動。

5. When the unit is running, pay attention to the explosion-proof safety door of the gas engine. In case of explosion (with loud sound), close the air source and replace the explosion-proof rubber before restarting.

三、天然氣發電機組停機應采取的措施

3、 Measures to be taken for shutdown of natural gas generator unit

1、正常停機時，應先使機組在怠速運轉至水溫、油溫降到60℃以下后再切斷氣源停機。

1. During normal shutdown, make the unit operate at idle speed until the water temperature and oil temperature drop below 60 ℃, and then cut off the air source for shutdown.

2、緊急停機后，應“盤車、泵油”至水溫、油溫降到60℃以下后再切斷氣源停機。

2. After emergency shutdown, turn the gear and pump oil until the water temperature and oil temperature drop below 60 ℃, and then cut off the air source for shutdown.

3、停機后，應將“電磁閥電源”開關置于“關（OFF）”位置，并關閉燃氣總閥門。

3. After shutdown, turn the "solenoid valve power" switch to the "off" position and close the main gas valve.

以上就是為大家介紹的有關天然氣發電機組的詳細介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以專業的態度,為您提供服務http://dgtmcnc.com

The above is the detailed introduction of natural gas generator set. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://dgtmcnc.com